Видео

Junk it and put a alternator on it

How much

i had the same issues when i picked up an old pontoon with an '87 Mercury 2 stroke 50hp... a lot of replacing parts..

When your hammer goes through the glass.....you just bought the guys boat.....rot and all.

Would you figure out with this boat?

No one is making videos on this😡 if I loosen it can it be reused if greased? Is the larger gear supposed to have play

Johnson?

All the 3.0l. Crack in the same spot 😂 we just fixed ours

Where can I find that exact throttle

Where do you get the dyno tester, nice bit of kit.

When you go buy a used Boat, nobody’s gonna let you beat on their boat with a hammer

Same thing with my motor. Had a misfire and had to get the wires and plugs changed.

Tohatsu outboard does not get gasoline into the cylinders. The injector, ecu, spark plugs are intact. When I pour gasoline into the pistons, it works a little. When you press the starter, oily gasoline comes out of the exhaust. Greetings from Turkey..

Thanks for sharing simple yet effective

wouldnt that be safer to have the water supply from the hose in the back rather than ear muffs.those motors dont run cool with ear muffs at that high rpm

Nice video on firing order numbers 3 only fires once in a while sounds like I have the same problem on my 125 force outboard the i rebuilt

nice engine but please dont rush around with the video so much...take your time and stand back some so the entire engine can be viewed..toward the end you at last showed all the torque converter housing set up; had to pause the video..slow down

Thanks for this ❤

Thanks for this ❤

Do you have on inline 6 available

Another technique is to get a timing light with a tachometer and clip the pickup to each spark plug wire to see if the rpms on each plug match.

If you really want it to push that pontoon, consider trying to fit a bigger lower unit on there that'll take a 14" prop.

I was afraid to hit that hard because I thought it would crack the gelcoat

The best money can buy 👌

So, certain psi = HP? What does the red tape mean? Wonder about the lake water deposits around the water jackets...🤔

Donde lobenden y cuanto

2023 год. Я катаюсь на таком моторе)

Bet it came from throttling down to fast and shutting it off right away

Shouldl it move that easy when it's still connected to the lines that go back into the boat (like if you disconnect the rod from the pivot pins in the front and rear and just have it hanging by the lines but not disconnected)?

Hello, i have a 1983 mercury TOP 90hp - we notice that the idle speed is very low and once in reverse going slow or in neutral for a extended period of time the engine will shut off. If I tighten the screw you did in the video will that raise my idle speed so going in reverse at slow speeds and staying in neutral the engine wont shut off? thanks for the help! great video by the way.

i have like 30 volt on each coil😅 what might be the issue? its only running on coil 2

That “it’s full of gas” line always gets me 1:05 😂

I tried this on a 250 mercury when the starter broke. I saw the emergency rope inside the cover and thought if it wasn’t possible they wouldn’t have put the rope in there. I couldn’t put that bitch over fast enough! I figured maybe they intended it as a two person job. After watching this I feel very weak 😂

These were great engines, durable, simple, rugged, and reliable.

That engine should be running a little hotter than normal if its firing that much.

have the same ... Please, whats the problem?

How power aprox. HP at the propshaft? Thanks

Hello! Did this plate is compatibke with volvo penta sx-m sterndrive? Is it available yet?

Where does that red and white wire from the stator connect to

What year model is that motor is that a pre mix or auto. Mix

How do you get that thing out. I've got the hex plug out .

Nice head

your video is to close up. you can't even tell where on the motor you went to. Just saying from a idiot point of view, I don't know motors and if your trying to teach it, I cant tell where you are.

HAAHAAA

The better compression a motor has the harder it will be so that's a good problem to have

The DVA used on this video is similar to Dangar Marine DVA.? I have checked my 1994 115 hp Evinrude and on all 4 cylinders reading was about 30/40 Volts. Engine Manual calls for 150 and up for that measure using a load resistance.

Where was the tell tale? I burned up the top cylinder that way. Water came out but not high enough to fill the block completely.

How much. Did you get

very helpful, have determined my vro pump is bad on my 2001 johnson 90 hp, so I started looking for videos of motors with bad vro pumps to see how they acted. mine acts just like this, so I guess, 500 dollars will fix it! thanks

Who is that stupid woman sitting plumb bang in the middle? So difficult to judge which side to jump if there is an idiot sitting down in the way